Mini Educator E Collar Instructions for Safe and Efficient Use

Author

Posted Nov 3, 2024

Reads 1.1K

Siamese Cat Wearing Colar Cone
Credit: pexels.com, Siamese Cat Wearing Colar Cone

To use your Mini Educator E Collar safely and efficiently, it's essential to understand the device's components and settings. The collar has three main buttons: the On/Off button, the Mode button, and the Stimulation button.

First, ensure the collar is properly fitted to your dog's neck, with the contact points in contact with the skin. This ensures the device functions correctly.

Before turning on the collar, familiarize yourself with the different stimulation levels, which range from 1 to 100. The collar also features a low battery indicator and a vibration mode for training.

Remember to always keep the collar out of reach of children and pets when not in use.

Getting Started

The ET-300 Mini Educator is an e-collar designed to help correct your dog's undesirable behavior and reinforce already learned commands. It's a valuable communication tool that fosters better relationships between pets and their owners.

You'll receive a comprehensive package that includes a handheld transmitter, collar receiver, and other essential accessories. The package content may vary slightly depending on the model, but it's always a good idea to check the box contents to ensure everything is there.

To get started, make sure to check the package contents and familiarize yourself with the included accessories. The ET-300 Mini Educator typically comes with a handheld transmitter, collar receiver, Biothane collar strap, dual lead charger, and other tools like contact point removal and skin removal tools.

What's Included

Credit: youtube.com, What's Included and how to get started

Getting started with your new device requires some basic knowledge of what's included in the box. The handheld transmitter is a crucial part of the setup.

You'll also receive a collar receiver that comes with a 33” long 3/4” wide Biothane strap, making it easy to attach to your dog's collar.

A dual battery charger is included to keep your device charged and ready to go. This is especially important if you plan on using the device frequently.

The contact points are a critical component of the device, and you'll receive two sets: 3/4” and 5/8”. Make sure to choose the correct size for your dog's collar.

A contact point tool and test light are also included to help you set up and test the device. These tools can be a bit tricky to use, so take your time and refer to the owner's manual if needed.

Here's a summary of what you can expect to find in the box:

  • Handheld transmitter
  • Collar receiver with Biothane strap
  • Dual battery charger
  • Two sets of contact points (3/4” and 5/8”)
  • Contact point tool
  • Test light
  • Lanyard
  • Owner's manual

How to Fit It

Credit: youtube.com, Setup & Fit | Getting Started With Your Iron Neck

Fitting the ET-300 e-collar correctly is essential for effective training and to prevent skin irritation. The collar should be adjusted to allow the "contact points" to have direct contact with the skin.

You should be able to fit a couple of fingers between the collar strap and your dog's skin. This is crucial to prevent skin irritation and discomfort.

The optimal position for the collar receiver is on either side of the dog's windpipe. This is where the contact points will work most effectively.

To prevent skin irritations, the Collar Receiver should never be worn for more than 12 hours per day. This will help prevent chafing and irritation.

Here are some guidelines for fitting the collar:

Rotating the collar every 2 hours will help prevent skin irritation and ensure consistent correction.

Training and Commands

To get the most out of your mini educator e collar, it's essential to understand the training and commands involved.

The mini educator e collar comes with a range of pre-programmed training modes, including a "nick" mode that provides a gentle correction to help your dog learn.

You can choose from various training modes, including nick, continuous, and momentary stimulation, to suit your dog's individual needs.

Training Your Dog's Stay Command

Credit: youtube.com, How to Teach your Dog to Stay in 3 Steps Force Free!

Training your dog's Stay command requires patience and consistency.

First, your dog needs to be able to hold the position, which means they can sit and remain in that position for a few seconds without getting up.

Once they've mastered this, you can layer over the e-collar static stimulation, just like you did with the Come and Place command.

To do this, put the e-collar and leash on your dog and go back to asking for Sit and Stay. If your dog breaks the sit behavior, apply light static stimulation using the Nick or Continuous button on your handheld transmitter.

Use your leash, body, treats, or words to guide your dog back into the position if needed.

Release the stimulation and give your dog a treat once they're back in the sit position.

Don't increase distance, duration, or distraction until your dog demonstrates they can understand the stay command with the static stimulation applied.

Additional reading: Dog Training Lead Leash

Are Effective?

Credit: youtube.com, Master Basic Commands For Your Dog With These Training Tips!

E-collars can be invaluable training tools, but only when used correctly. If you are unsure about using one or don't know how to start, please consult with a professional trainer.

Using an e-collar requires careful consideration and proper technique to avoid confusion or even harm to your dog.

There's no one-size-fits-all approach to training with an e-collar, and what works for one dog may not work for another.

Is Your Pet Ready For Adjustment?

A flashing "1D" on the LCD screen of your ET-300 Mini Educator e-collar indicates the stimulation can be adjusted.

If you see this flashing light, it's a clear sign that your pet is ready for adjustment.

Device Features

The ET-300 Mini Educator e-collar has some amazing features that make it a favorite among pet owners and trainers. It has a round remote transmitter that's easy to hold and use with one hand.

The device comes with 100 levels of static stimulation, plus an extra 60 levels of boost for when your dog needs a little extra motivation. This is perfect for high-distraction situations or stubborn dogs.

Credit: youtube.com, ECollar Setup Tutorial - ET 300 mini educator

Here are the device's key features:

The ET-300 Mini Educator is designed to be user-friendly and adaptable to different situations. It's great for training in various environments, from your backyard to the local park or even on a boat.

Characteristics

The ET-300 Mini Educator remote training collar is a feature-packed device that delivers big performance in a small package. It has a unique round remote transmitter, reminiscent of a stopwatch, making it easier to hold for one-handed operation.

The remote transmitter is waterproof and even floats in water, so you don't have to worry about it getting damaged in case you drop it. The range of the device is an impressive ½ mile, making it perfect for training your dog in the backyard or at the local park.

The ET-300 Mini Educator supports three stimulation modes: momentary, continuous, and combo mode. It also has a tapping sensation or tone/stimulation feature, which is great for deaf dogs and stimulation-sensitive dogs.

Credit: youtube.com, Defining Characteristics of a Medical Device

Here are the key characteristics of the ET-300 Mini Educator:

  • Range: ½ Mile
  • Three Stimulation Modes Supported
  • Tapping Sensation or Tone/Stimulation (Pavlovian Conditioning)
  • Tapping Sensation: Alternative to Stimulation (gives vibration similar to a Cell Phone)
  • Tone Stimulation: After 1.2 seconds of tone, the collar will send stimulation as long as the button is pressed (up to 10 seconds)
  • Quick Charge Li-Polymer Batteries
  • Convenient Intensity Dial for Quick Adjustment Stimulation Levels Adjustable from 0 to 100
  • Collar Receiver Light for locating your dog at night
  • Lock and Set Stimulation Safety Feature
  • Stimulation Boosting Mode provides instant control when normal stimulation is ignored – great for emergency situations.
  • User Adjustable Boosting Levels from 1 to 60 Levels
  • Completely Waterproof
  • Convertible from 1-Dog 300 to 2-Dog 302

The ET-300 Mini Educator also has a stimulation boosting mode that provides instant control when normal stimulation is ignored – great for emergency situations. This feature, combined with the user-adjustable boosting levels, makes it a powerful tool for training your dog.

Full Range Limitation

The actual range of your e-collar can be affected by training conditions, including weather and terrain. This means you might not always get the full range you're expecting.

For most dog training, a 3/4-mile range is more than enough. However, it's worth noting that this can vary depending on the conditions you're in.

To get the best results, it's a good idea to hold the transmitter away from your body. This will help you get the maximum range out of your e-collar.

If you touch the antenna, it will significantly reduce the range. So, try to avoid that if you can.

The lost transmitter mode is automatically turned off when the transmitter is turned off and back on again.

How it Works

Credit: youtube.com, How to use your Mini Educator E-collar

The ET-300 Mini Educator is a powerful tool for training your dog, and it's surprisingly easy to use. The device consists of a transmitter remote and a receiver collar that your dog wears around their neck.

The transmitter remote sends a signal to the receiver collar, which has two contact points, or prongs, that deliver static. This is the primary way the collar communicates with your dog.

You can also set the remote to deliver vibration or Tone, which can be a great alternative to static in certain situations. These options allow you to tailor your training to your dog's individual needs and preferences.

In highly distracting situations, you can use the boost option to increase the effectiveness of the collar. This feature can be a lifesaver when your dog is easily distracted or resistant to training.

Here are the key features of the ET-300 Mini Educator's modes:

  • Static: delivers a static correction to mark the message
  • Vibration: delivers a vibration to mark the message
  • Tone: delivers a tone to mark the message
  • Boost: increases the effectiveness of the collar in distracting situations

Operating the Device

To turn on the ET-300 Mini Educator e-collar, place the small dot on the transmitter remote against the small dot on the receiver collar, then press the “L” button for 2 seconds.

Credit: youtube.com, How to Program the ET-300 Mini Educator E-Collar - 1 Dog System.

You can also turn it off by pressing and holding the “L” button for 2 seconds. This is a simple and quick way to conserve battery life.

The device has a tracking light that can be activated by pressing the “L” button, which is especially useful for locating your dog after dark. The light button cycles through flashing, solid, and off modes with each press.

Operating

Operating the ET-300 Mini Educator e-collar is a straightforward process. You'll need to pair the transmitter remote with the receiver collar by placing the small dot on the transmitter against the small dot on the collar.

To turn on the device, press the "L" button for 2 seconds. This will activate the transmitter and receiver. If you're having trouble getting the range, remember to hold the transmitter like the torch on the Statue of Liberty – keep the antenna away from your body or fingers.

Hand Touching Vintage Brooch Pinned to Collar
Credit: pexels.com, Hand Touching Vintage Brooch Pinned to Collar

You can check if the device is locked by looking at the LCD screen. If it's locked, "1D" will be solid instead of flashing.

Here are the basic steps to turn the device on and off:

  • Place the small red dot on the transmitter against the small red dot on the collar receiver.
  • Press the "L" button for more than 2 seconds to turn it on or off.

To turn off the device, simply press and hold the "L" button for 2 seconds. This will shut down the entire system.

If you need to lock the stimulation level, push down on the top of the stimulation dial. "1D" will light up on the LCD screen, and if it's unlocked, this will be flashing.

Charging Your

Charging your ET-300 Mini Educator e-collar is a straightforward process. The charging port can be found at the back of the remote transmitter and collar receiver, where you'll also find the dual charger.

To charge your device, simply lift the flap and attach the dual charger. This will get your remote and transmitter batteries charged in no time.

The light on the charger will turn RED during charging cycles, which can take approximately 2 hours. Once fully charged, the light will turn to GREEN.

It's worth noting that the battery life of your ET-300 e-collar is quite impressive, lasting between 40-60 hours on a single charge.

Here's an interesting read: E Collar Remote

Pairing a New Device to the Transmitter

Full body side view of young female owner training Labrador Retriever with collar while sitting on grassy ground in countryside
Credit: pexels.com, Full body side view of young female owner training Labrador Retriever with collar while sitting on grassy ground in countryside

Pairing a new collar to the ET-300 transmitter is a straightforward process. To start, turn on the remote and press the red "S" button, then the black "S" button, and finally the "T" button, holding all three simultaneously for 2 seconds or until the confirmation beep is heard.

This changes the remote to a 2-dog remote, allowing you to add another collar. To pair the new collar, follow the pairing/syncing steps outlined previously: simply turn the remote on and follow the steps.

The first step is to turn on the remote, then press the red "S" button, followed by the black "S" button. Next, press the "T" button and hold all three simultaneously for 2 seconds or until the confirmation beep is heard.

This indicates that the remote is now ready to pair a new collar. To confirm, simply follow the pairing/syncing steps outlined previously.

Here are the steps to pair a new collar in a concise format:

  • Turn the remote on.
  • Press the red “S” button.
  • Press the black “S” button.
  • Press the “T” button and hold all three simultaneously for 2 seconds or until the confirmation beep is heard.
  • Follow the pairing/syncing steps outlined previously.

Converting to a 1-Dog Remote System

Credit: youtube.com, Selecting an Operating Mode on Your SportDOG A-Series E-Collar System

To change your ET-300 back to a single-dog system, you'll need to follow a specific sequence of button presses.

Press the red "S" button, then the black "S" button, and finally the "T" button to initiate the change process.

This sequence of buttons will prompt the device to switch back to a single-dog remote system.

Press and hold all three buttons simultaneously for 2 seconds or until you hear the confirmation beep.

This beep is your assurance that the change has been successfully made and your ET-300 is now set up for a single-dog system.

Using the Boost Function

To send momentary or continuous boosted stimulation, press the red "S" button. This will activate the boost function.

The default boost level is 5, but you can adjust it to any value between 1 and 60. This is especially useful for smaller breeds, which should use levels 1 through 20, while larger breeds may need more of a boost.

Credit: youtube.com, How to Set the BOOST Function on the EZ-900 EducatorE-Collar

To use the momentary boost, press the black "S" button first, then press the red "S" button without releasing the black. For continuous boost, press the red "S" button first, then the black "S" button without releasing the red.

Here's a quick summary of the boost function:

The boost function adds to the set stimulation level, so if your e-collar is set to level 10 and the boost is at level 5, your dog will receive 10+5 stimulation.

Activating Night Tracking

To activate the night tracking on your ET-300 Mini Educator, you'll need to press the "L" button on the back of your remote for half a second. This will turn the night tracking light on, and you'll know it's working because the light will start flashing.

The light will continue to flash until you press the "L" button again, which will switch it to solid mode. Press the button one more time to turn the light off altogether.

Here's a quick summary of the steps:

Replacing Contact Points

Portrait of a Dog in a Chain Collar
Credit: pexels.com, Portrait of a Dog in a Chain Collar

Replacing Contact Points is a relatively straightforward process that requires the right tool and a bit of patience. You'll need to use the included contact point tool to loosen the old contact points by rotating them counter-clockwise.

The contact point tool is usually provided with the device, so make sure you have it on hand before starting the replacement process. Loosen the contact points in a clockwise direction to prevent any accidental tightening.

To install the replacement prongs, simply reverse the process and rotate them clockwise to tighten. This will ensure a secure connection and prevent any loose contact points.

Here's a quick summary of the steps:

  • Loosen old contact points by rotating counter-clockwise
  • Install replacement prongs and tighten by rotating clockwise

Remote Transmitter

The ET-300 Mini Educator remote transmitter is a distinctive round, stopwatch-like shape. This unique design makes it easy to identify and use.

To pair a new collar to the ET-300 transmitter, follow these steps:

  • Turn on the remote
  • Press the red "S" button, then the black "S" button, and finally the "T" button
  • Hold all three buttons simultaneously for 2 seconds or until the confirmation beep is heard

This changes your remote to a 2-dog remote, allowing you to add another collar. Simply follow the pairing/syncing steps outlined previously to pair the additional collar with the transmitter.

The ET-300 transmitter has a range of up to 1/2 mile, making it suitable for training in open areas.

Stimulation and Modes

Credit: youtube.com, How to change the boost level on a Mini Educator e-collar | Follow The Leader Dog Training

To set the stimulation level on your ET-300 remote trainer, simply rotate the stimulation level lock at the top of the remote clockwise to increase the level or counter-clockwise to lower it.

You can switch stimulation modes in your ET-300 by pressing the "M/C" button at the back, which allows you to change between the three stimulation modes as needed. When in combo Momentary/Continuous mode, the LCD screen will show both "M" and "C" on the screen.

Momentary stimulation sends a single pulse of stimulation, while Continuous will send pulses of stimulation for as long as the button is pressed, timing out after 10 seconds. This is a safety feature designed to prevent accidental over-stimulation of your dog.

You can change stimulation levels while pressing the remote buttons, but only when using Continuous stimulation mode. This is a convenient feature that allows you to adjust the stimulation level as needed without having to stop the stimulation.

Credit: youtube.com, E Collar Training For Beginners: Acclimation to Stim

Here's a quick reference guide to help you understand the stimulation modes:

Remember, the stimulation is meant to distract your dog from doing something they're not supposed to, not to hurt them. The ET-300 also comes with vibration and tone training options for people who prefer not to use static.

Will an E-Herb Hurt My Dog?

The E-Herb is an electronic device that sends a signal to the dog's neck, which can be in the form of static shock. This stimulus is meant to distract the dog from undesired behavior.

The stimulation is generally harmless, but may be unpleasant for the dog. It's worth noting that some people may prefer not to use static, as the ET-300 also comes with vibration and tone training options.

The vibration and tone training options are a great alternative for those who want to avoid static. They can be just as effective in training the dog.

See what others are reading: Vibration Collar vs Shock Collar

Stimulation Modes

Medium Short-coated Tan and White Dog With Brown Collar on Focus Photo
Credit: pexels.com, Medium Short-coated Tan and White Dog With Brown Collar on Focus Photo

You can set the stimulation level on your ET-300 remote trainer by rotating the stimulation level lock at the top of the remote. Rotating clockwise increases the level while counter-clockwise lowers it.

The ET-300 remote has two stimulation modes: momentary and continuous. Momentary stimulation sends a single pulse of stimulation, while continuous stimulation sends pulses for as long as the button is pressed, timing out after 10 seconds.

You can change stimulation levels while pressing the remote buttons, but only when using continuous stimulation mode. If you're using momentary stimulation, you won't be able to change the level while the button is being pressed.

There are three stimulation modes on the ET-300 remote: momentary, continuous, and combo momentary/continuous mode. Combo mode displays both "M" and "C" on the LCD screen when selected.

Here's a quick summary of the stimulation modes:

You can switch between these modes using the "M/C" button on the back of the remote.

Frequently Asked Questions

What is the T button on the mini educator?

The "T" button on the mini educator sends either a tapping sensation or tone stimulation to the collar receiver, which can be toggled by pressing the "L" and "T" buttons simultaneously when the intensity level is "0". This feature allows for customizable training options.

What does m and c mean on mini educator?

The "M/C" button on the Mini Educator transmitter allows users to switch between three stimulation modes, including Momentary Mode. This mode is activated by pressing the Stimulation Button "S" and Stimulation Booster Button "S

What do the buttons on the E collar do?

The E collar features three primary buttons: the "t" button, the black "s" button, and the red "s" button, each with a specific function. By understanding how to use these buttons, you can effectively operate the collar.

How to change mini educator settings?

To change mini educator settings, scroll up to the desired number and tap the black button. This will allow you to customize the settings to your preference.

How do you reset the remote on the e collar?

To reset the remote on the e-collar, press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. This process typically requires holding both units 2-3 feet apart.

Kelvin Gutkowski

Lead Assigning Editor

Kelvin Gutkowski is a seasoned Assigning Editor with a passion for storytelling and a keen eye for detail. With a background in journalism, Kelvin has honed his skills in identifying and assigning compelling stories that captivate readers. His expertise spans a wide range of topics, from social justice to environmental issues.

Love What You Read? Stay Updated!

Join our community for insights, tips, and more.