Using a shock collar can be a effective way to stop barking quickly and safely. This method is particularly useful for dogs with persistent barking problems.
First, it's essential to choose the right type of shock collar for your dog. According to the article, there are two main types: bark-activated and remote-controlled shock collars. The bark-activated collar emits a shock every time your dog barks, while the remote-controlled collar allows you to administer the shock at your discretion.
The intensity of the shock is also crucial to consider. The article suggests that a low to moderate intensity setting is usually sufficient to stop barking, as high intensity settings can be painful and even lead to long-term psychological damage.
A fresh viewpoint: E Collar Remote
Choosing the Right Equipment
Choosing the right equipment is crucial when it comes to using a shock collar to stop barking. Make sure to fit the remote training collar properly to ensure effective operation.
To fit the collar, start by turning it off and letting your dog stand comfortably. Check the fit by putting one finger between the collar and your dog's neck - the collar should be snug. Don't fit the collar while your dog is sitting down, as this can make it difficult to get an accurate measurement.
You should also let your dog wear the collar for a few days to a week before starting active training, as this will help prevent them from becoming "collar-wise". This means they'll associate the correction with bad behavior, not the collar itself.
Here are some types of bark collars you can consider:
Properly Fitting a Remote Training Collar
Properly Fitting a Remote Training Collar is crucial for effective operation. It's essential to make sure the collar is turned off before fitting it on your dog.
First, let your dog stand comfortably, rather than sitting down. This will make it easier to get an accurate fit.
To check the fit, put one finger between the collar and your dog's neck. The collar should be snug, but not too tight.
It's also important to let your dog wear the collar and get comfortable with it for a few minutes before rechecking the fit. This will help your dog adjust to the new sensation.
Here's a quick checklist to ensure a proper fit:
- Make sure the collar is turned off
- Let your dog stand comfortably
- Check the fit by putting one finger between the collar and your dog’s neck
- The collar should be snug
- Let your dog wear the collar and get comfortable with it for a few minutes
- Recheck the collar to ensure perfect fit
Remember, it's best to let your dog wear the electric training collar for a few days up to a week before starting active training. This will help your dog associate the correction with the bad behavior, rather than the collar itself.
Static Collars
Static collars are a type of training equipment that can be effective in correcting excessive barking in dogs. They send a static shock stimulation to your dog when it senses barking.
These collars are suitable for stubborn, determined dogs that have tried everything else. They're also more economical than working with a dog trainer consistently.
You might like: Dog Collars
To use a static collar correctly, start with the lowest level of shock and gradually increase it to your dog's tolerance. This will help your dog accept the correction and change the bad behavior.
A static collar should not be left on your dog for more than 10 hours at a time. It's essential to use them under supervision for a few hours at a time.
To ensure the collar fits your dog correctly, you can put a finger between the receiver collar and the dog's neck. If it's too loose or too tight, it can hurt your dog's skin or cause breathing difficulties.
Here are some types of bark collars:
- Bark Shock Collars
- Spray Bark Collars
- Anti Bark Vibration Collars
Using the Shock Collar
First, you need to select the correct contact points based on your dog's fur type. If your dog has thick fur, use long contact points and conductive silicones, while short contact points and conductive silicones are best for dogs with thin fur.
To ensure the collar fits correctly, put a finger between the receiver collar and your dog's neck. If it fits snugly, you're good to go.
Start with the lowest level of electric shock function and gradually increase it to help your dog accept and change the bad behavior.
Don't leave the bark collar on for more than a few hours at a time to avoid irritating your dog's neck.
Training and Safety
Using a remote collar can be a fabulous way to train and build a better relationship with your dog. It's not just a tool for correction, but also for communication.
A "last resort, push the button out of frustration" mindset is not only ineffective, but it can also damage your relationship with your dog.
Using a remote collar requires a thoughtful and intentional approach to training. This means considering your dog's individual needs and personality.
Suggestion: Shock Collar Not Working on Dog
Sources
- Remote Dog Trainer: How To Use a Dog Training Collar? (thedogline.com.au)
- Simple Guidance For You In Use Shock Collar (patpet.com)
- How to train a dog to stop barking using e-collar (petspy.com)
- YouTube (youtube.com)
- static shock collar (edogaustralia.com.au)
- bark collars (edogaustralia.com.au)
Featured Images: pexels.com